Tag: Orange pi

Orange Pi Zero 2 : A new Raspberry Pi contender ?

The new Orange Pi Zero 2 Single Board computer

If you were searching for a very small and capable SBC to run some linux app on arm cpu , you were already able to buy the original Orange PI zero ,
but the board has some obvious flaws like .

  • 100mbps ethernet
  • very unreliable wifi
  • no display connector
  • Unreliable power connector (MicroB)

Now after a few years, the company responsible for the original board has created a successor with updated specs.
The size of the board is larger than the first , but this is still one of the smallest SBC available on the market at 60 x 53 mm

Bigger than the original OrangePi Zero

Here are the complete specs :

  • SoC – Allwinner H616 64-bit quad-core Arm Cortex-A53 processor @ up to 1.5 GHz with Arm Mali G31 MP2 GPU
  • Memory – 512MB or 1GB DDR3
  • Storage – MicroSD card slot
  • Wired Networking – Gigabit Ethernet
  • Wireless Networking – Dual-band 802.11 b/g/n/ac WiFi 5 + Bluetooth 5.0
  • USB – 1x USB 2.0 host port, 2x USB 2.0 interfaces via 13-pin header
  • 13-pin header with 2x USB, analog stereo audio output, CVBS video output, IR input, 3x GPIOs
  • 26-pin IO header with I2C, SPI, UART, multiple GPIOs
  • Debugging – 3-pin UART header for serial console
  • Power Supply – USB Type-C port 5V
  • Dimensions – (60 x 53 mm)

All this for a board that cost less than 20euros !
looking at the cpu, we have a quad core that might be able to match the performance of a raspberry pi4 but when you look at the cost , it’s more in competition with the Raspberry PI zero W witch has a lot less features than this board and is way less powerful !

I can completely see that board screwed behind a screen and used has an emulation machine .
Or a IP security camera server using MotionEyeOs
Or connected to a ISP router to run pihole (but i would still prefer the original pi zero for this , this one is too powerful for pihole).
Maybe a domotic server like Domoticz or Jeedom , the possibilities are endless !

The main flaw of this new board is the USB port . It’s only a USB2.0 port , and it will limit pretty severely the kind of projects that you can realistically do on this board,
Even if USB2 still has a 300mbps bandwidth. I would choose a board with USB3 to run a server like OpenMediaVault.

you can buy this board here

Orange pi zero – the battle against HEAT

As you know if you own the orange pi zero, the board run very hot. Running it without an heat sink is not really possible if your board is doing anything other than idling

and even with an heatsink you will encounter throttling if your application is a little intensive.

In an other article I managed to get a fan running controlled by the gpio’s.

A cron check every minute the cpu temperature, if it’s above a set temperature, the fan turn on.

On this photo you can see the NPN transistor fixed to the fan

 

If it’s under, the fan turns off.

The first time I did that project it was on my first orange pi zero. I made some mistakes in my wiring and, because of that, the fan only received 2.5v, it was spinning very slowly, and I was obliged to do some bash trickery to get the fan to start.

My original orangepi zero was lost during an apartment change.

I decided to order a new one and this time, I wanted to do the best work I could to integrate the fan and heatsink.

I found an acrylic case for the orange pi zero on aliexpress.

And after receiving my orange pi zero, I saw the board was a new revision, it was running even hotter than my previous orange pi zero.

Few days after receiving the board, the case arrived. It was very pretty but it was blocking any air circulation. And the heatsink had no medium to dissipate the heat since the air was hot and not circulating around the metal.
The CPU temperature rapidly ascended to 80°c.

I own several old fans disassembled from old graphics card, and one of the small fans was just the perfect size. I cut a circular hole in the top acrylic plate so the air from the fan could enter and go trough the radiator fins. The air should after exit from a void in a face of the case were optional usb port are placed.

How to use that fan?

The problem with gpio’s is that they only push very weak current and volts (3.3v). You cannot run a fan directly from a gpio.

But you can use a gpio to control an electronic switch (a transistor) that will be able to run the fan

You should use a npn transistor. They are the most common and cost next to nothing. You will find them for free when you tear down old broken power supply.

To turn on and off your switch, you just have to send 1 or 0 on it’s base.

A great way to control the gpio’s of the opi zero is with the help of that library called WiringPI

you will find instructions on how to install the library on the github page.

after installation lauch the command gpio readall

 

i chose the gpio.7 to control my fan ,

conveniently the gpio 7 is placed in the 7th place on the board , and his wPi alias is also 7

as you can see in the attached capture it’s not always the case !

 

 

 

 

 

 

i then solder my fan and transistor following this diagram :

To continue , i must write a script that check for the cpu temperature , and activate the fan if the cpu temperature is above a certain set threshold.

then , using crontab , set this script to launch every minutes.
add the line * * * * * /root/fan-control.sh to your cron jobs , using the command crontab -e

thanks to this script your fan should automatically launch when your Orange is charged , and stop when it’s return to idling.

Orange PI Zero Plus – A simple and, powerfull SBC

if you follow what’s new in the SBC world. You must know Xunglong Orange pi, they are a Chinese manufacturer known for making very cheap sbc’s based on Allwinner chip’s.

One of their most interesting sbc’s was the orange pi zero. It was small, powerful, and was ideal for a small headless server. (still available)

It was extremely cheap: less than 10€ but was plagued with some issues like very poor wifi stability, and poor software support from the manufacturer and, only 100mbps on the Ethernet port.

 

Now Xunlong has come up with an improved version of this board.

  • The wifi chip is now a well supported Realtek RTL8189FTV
  • The Ethernet port is now capable of 1Gb/s transfer rate
  • The cpu is improved with an Allwinner H5
  • The layout stay exactly the same so case are compatible.

I’ve already ordered one of these boards. At 16,02€ including shipping

It’s available at Aliexpress

OrangePI : Install OpenRTSP on a ARM device

One of my project with my OrangePI is to setup the device as a basic IP security camera server ,

the OrangePI zero , will connect to RTSP flux of the IP camera , and dump the stream on to an external disk , where it will be kept for 7 days before getting automaticly deleted
At a latter date i will run a motion detection program on these files and send a mail if motion is detected on a specific part of the frame.

after a little research , i found that a lot of people are using a program called openRTSP to record their RTSP stream to disk

But , after connecting on my OrangePi zero and trying to look for the program i found out that it’s not part of the default installation of armbian stable.

I tried to install the package using apt install openRTSP

I went to google and searched , openRTSP package ,and found out , on the debian website that openRTSP is part of the livemedia-utils package,

I went back to my SSH session and typed apt-get install livemedia-utils

There is no man pages associated with the program , you have to rely on the developer website to understand all the different options . The documentation is available here : http://www.live555.com/openRTSP/  or here if the website is down.
but as usual , in the officials repositories you only get dated version

you might want to compile the source code to have the last version available:

as root

Go to /usr/src: cd /usr/src
Get the live555 liveMedia source code: wget http://www.live555.com/liveMedia/public/live555-latest.tar.gz
Unpack it: tar -xzf live555-latest.tar.gz
Go into the  unpacked directory: cd live
Generate the make files: ./genMakefiles linux
Build the code: make
Install the latest version: make install

The new Orange pi  Zero Plus 2 |allwinner h3, 512mb, 4K hdmi, 8gb emmc

orange pi is an awesome sbc manufacturer known for excellent hardware and awful software support. 

I’m a very happy owner of the first generation orangepi zero witch I use as a headless Linux server on my network. 

Today orangepi release a new version of the orange pi zero called the “orange pi zero 2 plus” the cpu goes from the H2+ to the H3, the wlan controller is better, you get a csi camera interface. And 8gb onboard mmc flash. 

Also the board gain an hdmi port witch enable easy video output to a screen or a TV. 

The board also gain bluetooth support if that something that’s useful to you. 

Overall its seems the addition of the hdmi port is at the expense of the disappearance of the ethernet port witch was for me one of the best feature of the first edition of the orange pi zero. 

The board is made for a different purpose, the 2 plus is going to be ideal for a very small media player or a emulator gaming device. Since the video output and the 4k capability are adding  this kind of possibilities 

The board is also much more expensive than its predecessor at 18$90 compared to the original 512MB orange pi zero at 8$99.

Since I don’t require a video output the original orangepi zero suits better my purpose, but for most people a video output is mandatory, 

The orange pi zero 2 plus is going to be be an excellent board once the armbian team release an image for it.